- Overview:
This product is a 100% solid, two component, clear
polymer coating that is mixed at a 1 to 1 ratio by
volume. Each kit contains a bottle of resin and a
bottle of hardener. The product cures to a clear, high
build, glass like finish that resists scratching,
yellowing and will not distort with age. Items coated
with it will become permanently preserved and
protected for your enjoyment throughout a lifetime.
This product will not exhibit blushing or sweat out
under high humidity conditions.
- Primary
use:
This product is commonly seen on bar tops and table
tops in many bars and restaurants.
- Application:
The product should be applied in two stages. The first
stage is referred to as the seal coat. The seal coat
is brushed on in a thin layer and is used to seal any
pores in the surface and prevent air bubbles from
forming in the following flood coats. This stage is
followed by the flood coat, which will flow and self
level, clean brushes or squeeges can be used to help
spread the epoxy. Flood coats are applied in 1/8"
layers at a time, as many as desired can be applied,
however one to three coats is average for most table
or bar coatings.
- Recoating/Between
Layers:
Recoating can usually be be done within 4 to 8
hours. If re-coated within this time period no sanding
is necessary between layers.
If your previous layer has fully dried, very light
sanding with 220 grit sandpaper is recommended to
achieve a good bonding surface. After sanding you
should wipe down with a solvent such as denatured
alcohol or acetone to remove any impurities from the
surface. (do NOT use mineral spirits)
- Imbedding
Pictures:
Objects, such as pictures, maps etc. can be imbedded
in this product during the pours. Most photo quality
paper does not require any special preparation however
sometimes thin paper objects must first be sealed with
a white glue or similar product to prevent the kleer
koat from fully penetrating the paper and causing it
to become transparent.
- Imbedding Solid
Objects (wood, rocks, shells, etc.)
All porous materials should first have a seal coat of
epoxy applied. This will prevent air bubbles from
occurring in subsequent flood coats. Usually the
objects can be set in place before
sealing.
- Working
Conditions:
For best results the
product must be used at temperatures from 70-80
degrees F. The room which you are working should be
clean, dry, dust and insect free. Settling dust can
often cause blemishes on the glassy
surface.
- Exterior
Applications:
Please not that although this product will resist
yellowing better than other epoxies it is NOT 100% UV
resistant. Continuous outdoor UV exposure over
months or years will cause the finish to lose its
gloss, cause gradual changes in color and possibly
warp.
- Storage
Conditions:
Liquids should be stored
in a cool, dry, dark environment. Product will last
for at least 6 months and many times will last longer,
but small testing should be done if in doubt. The
hardener may get more amber in color as it gets older,
but this does not affect the use of the product.
Coverage:
See the coverage charts shown below to calculate the
amount you will need for your area. Remember not to
combine seal and flood coat coverage's. Flood coats
are designed to go on approximately 1/8" thick, which
is about three times thicker than that of a seal
coat.
Example: A
6ft x 4ft bare wood table (24sq ft) would require 2
Quarts to complete ONE seal coat and about a gallon and a
half to complete ONE flood coat for a total of Two
Gallons.
Beginners
Notes:
This material leaves professional results when
applied correctly so take your time and make
sure to beware of these of the common problems
we have seen encountered by first time
users.
1. Always make sure that your mixing
container is clean and your measuring device is
accurate, this product REQUIRES that you mix at
a 1 to 1 ratio by weight or volume, any
variances from this can cause the epoxy to stay
soft and not fully cure.
2. This product requires a THOROUGH
mixing, usually between 4 to 5 minutes of solid
mixing without excessive whipping of the
mixture(whipping will put lots of air bubbles
into the epoxy). Mixing one gallon at a time can
require up to 6 to 7 minutes of mixing.
Beginners should never attempt to mix more than
one gallon total per batch, 2 quarts per batch
is suggested until you feel comfortable with how
the product works.
3. After the two components are poured
together and stirring begins the mixture will
turn a cloudy white color, this represents areas
in which the epoxy has not fully combined. You
must continue to mix until all signs of
cloudiness and tiny white lines have completely
disappeared (usually takes 3-4 minutes of
thorough mixing).
4. Always scrape the sides of your mixing
container and also the stick during those 3-4
minutes. If UNMIXED epoxy remains on the side of
the container or the stick it will cause wet
spots on your finished product if that UNMIXED
material falls into your project......Followup:
While pouring your epoxy onto the surface NEVER
scrape the container to remove every last drop,
because no matter how thorough you mix there
will always be an unmixed drop on the side of
the container that will leave a wet
spot.
|
Recommendation
of Materials Needed For Application
(Link is attached to the materials if we
carry the product)
|
|
|
Safety
Gloves
- Epoxy can be very sticky
|
|
|
Graduated
Mixing Cups
- An accurate measurement is extremely important
to achieve optimum curing.
|
|
|
CLEAN
Stir Sticks
- Any dirt will end up showing on your product.
Mixing is very important, if you whip while
mixing you will end up with air bubbles, long
thorough stirs are required.
|
|
|
Applicators
- Rubber squeeges are simple to use and leave no
air bubbles. Foam brushes and nylon bristle
brushes are preferred with epoxy, make sure
there are no loose hairs.
|
|
|
Hair Drier,
Heat Gun or Torch - These are used after the
pour is completed and the epoxy is still liquid.
A very smooth stroke across about 6-12 inches
above the epoxy surface will burst remaining air
bubbles.
|
|
******************
Cold Weather
Warning ***************
|
|
If your epoxy
arrives cold during shipment is must be allowed
to acclimate to at least 75 degrees F before
using. Mixing this product below 75 degrees will
increase the potential for under-mixed epoxy
which will create wet or sticky areas on your
surface. Cold temperatures will also trap more
very tiny air bubbles during the mixing which
cannot always be removed with the torch/heat
gun. To warm the epoxy quickly we recommend
using either a heat lamp, an electric heater or
placing the closed bottles of epoxy in a tub of
warm water for 30 minutes. Getting the epoxy too
hot will result in a faster reaction time, so
pay careful attention to what you're
doing.
|
|
******************
Cold Weather
Warning ***************
|
Order
Online or by Phone:
561-588-1001
|
